loading  Loading... Please wait...

Plastic Bath Bomb Molds (pack of 10)

  • Image 1
  • Image 2
Calculated at checkout
**Price after discount is applied at checkout.

    Product Description

    Bath Bomb Molds

    This 2 piece plastic bath bomb mold has it all! Sleek, sturdy design, with an airtight seal along with a pre-punched eyelet that makes hanging and displaying your product simple.

    To use the mold: fill each side pretty firmly, add a little extra bath bomb material to the center to keep it all together, and press the mold together. To avoid any imperfections on your bath bomb, make sure to direct pressure to the edges of the mold rather than the center. Don't forget to line up the eyelets of each side when molding. Note, if the mold is packed too firmly it can make it difficult to open and close the packaging.  

    Mold Capacity: 4.88 oz

    Mold Cavity Diameter: 2-9/16

    Note: mold edge and eyelet add 1" to total package diameter.

    Find Similar Products by Category

    Write a Review

    Product Reviews

    Showing reviews 1-10 of 24 | Next

    Disclaimer: While we work to ensure that product information is correct, WE DO NOT MONITOR REVIEWS FOR ACCURATE INFORMATION. WE STRONGLY INSIST THAT YOU DO NOT TAKE MEDICAL ADVICE FROM ANY REVIEWS OR ASSUME THAT A PRODUCT WILL WORK THE SAME FOR YOU AS IT DID FOR OTHERS. Every consumer is different, circumstances vary and interpretations of results vary. These reviews allow consumers to share their experience with products but WE DO NOT VERIFY THE LEGITIMACY OF REVIEWS. These reviews are not intended to substitute for advice given by a physician, pharmacist, or other licensed health-care professional. You should not use this information as self-diagnosis or for treating a health problem or disease. Contact your health-care provider immediately if you suspect that you have a medical problem. Information and statements have not been evaluated by the Food and Drug Administration and are not intended to diagnose, treat, cure, or prevent any disease or health condition. BulkApothecary.com assumes no liability for inaccuracies or misstatements about products in these reviews.

    1. Should I have 2 different sizes so they can close? 3 star review

      Posted by on

      So I brought these awhile ago as a STEAM DIY sensory friendly Girl Scout project idea. I’m just looking the molds over for the event and I’m confused since they’re all the same size - how do I get them to close? The display photo looks like they snap together, am I misunderstanding the picture? I did the 3stars since I’m unsure if my set is correct...

    2. Nice size 3 star review

      Posted by on

      I liked the size, but hard to unmold once filled. The plastic is flimsy and dents easily. I ended up using my old molds.

    3. Nice size 3 star review

      Posted by on

      I liked the size, but hard to unmold once filled. The plastic is flimsy and dents easily. I ended up using my old molds.

    4. Worked well 4 star review

      Posted by on

      I bought these to shape the bath bombs, not to seal up and deliver as part of the bath bombs. They worked very well for the way I intended to use them. I wasn't able to cleanly close them, so what I did was fill each side, pack it down, add a pile more filling, close up as much as possible, twist back and forth to get rid of most of the excess, and squeeze a bit to make sure the bath bomb didn't split down the middle. Then I took one of the two lids off and set the bath bomb out to dry. Once dry, most came out of the other plastic piece easily. About half had to be twisted and tapped a bit to get the bath bomb out, but they did come out. My plan is to put the completed bath bomb in cellophane and wrap a ribbon around to close. So, for my purposes, these worked well. I'm sure other people were successful at closing theirs properly, but I want to re-use these. I've seen reviews suggesting they are flimsy. If they were thicker, I think it would be harder to get the bath bomb out, so I'm ok with the thickness. Thin plastic like this will not last forever - I have soap molds that are thin plastic and eventually they break. But the price was good, so I'll replace them if they break apart over time.

    5. Pretty good 4 star review

      Posted by on

      These plastic bath bomb molds are a bit small but they are pretty good to use. The best part is my bath bombs do not break. Pretty good for the price.

    6. I'll stick with regular molds 3 star review

      Posted by on

      I bought these thinking they would be great to use so I wouldn't have to wrap my bath bombs. I had a few issues with them. When filling them up it's hard to get them closed, the filling fills the outside area that is smashed and it looks messy. They do dent easily, and again, don't look nice. They are also very hard to get open-which is a good thing but the pressure you use to try and open them cause them to break apart. Not good. One thing I did do was use a similar size metal mold and then once I got it done placed it in this mold because I have them now and used it that way. Looked nice for display, it is what it is. I will not reorder this product again, it's just not something I want to mess with anymore.

    7. Great product. 5 star review

      Posted by on

      Great for the beginner.

    8. Bath Bomb Molds 4 star review

      Posted by on

      I like they are BPA free and responable priced. Great idea, use right in for packing. Great for first timers for practice. Not super sturdy but not
      fragile either. I will purchase again.

    9. Okay for price 3 star review

      Posted by on

      I used these my first time making bath bombs and I could never get the sides to fill in well enough to have my bath bombs stick together. I found that when they did work, I would try to release them and end up with dented sides since the plastic was too flimsy and would cave in as I tried to release the bath bomb. Overall they did work though, as long as you just kid of left them alone

    10. Meh 4 star review

      Posted by on

      I was originally using plastic ornament molds but they kept cracking so I got these thinking there a soft plastic so should work pretty well! The problem is they bend very easily and there's a weird indention on one side of them that the mixture sticks in to and then when I try to take them out those piece won't break apart hence, making the bomb crack down the middle and I end up having 2 halves. It wasn't with everyone but it was 6 out of 18! But they're cheap and easy to use so I'll keep using them just for cost reasons!

    Showing reviews 1-10 of 24 | Next

    Customers Who Viewed This Product Also Viewed